使用多槽手動超聲波清洗機能夠對各種工件進行快速的清洗，很多人工沒有辦法清洗干凈的縫隙、孔洞，都能在多槽手動超聲波清洗機中得到有效清潔，所以現在這種超聲波清洗設備廣受應用。那么怎樣才能讓多槽手動超聲波清洗機清洗的更加干凈呢？

The use of multi slot manual Ultrasonic cleaning can quickly clean various workpieces. Many gaps and holes that cannot be cleaned manually can be effectively cleaned in the multi slot manual Ultrasonic cleaning, so this kind of ultrasonic cleaning equipment is now widely used. So how can we make the multi tank manual Ultrasonic cleaning cleaner cleaner?

如果想讓多槽手動超聲波清洗機達到更好的清洗效果，那么就要注意外接的純凈水能否達到要求的純度，因為超聲波清洗機在作業時，對電導率和電阻都有一定的要求，而水質的純度不同，其電導率和電阻也都會不一樣，所以為了提高清洗的潔凈度要注意清洗機中使用的純水品質良好。

If you want to achieve a better cleaning effect of the multi tank manual Ultrasonic cleaning, you should pay attention to whether the external purified water can reach the required purity. Because the Ultrasonic cleaning has certain requirements for conductivity and resistance when operating, and the conductivity and resistance will be different due to the different purity of water, so in order to improve the cleanliness of cleaning, you should pay attention to the good quality of pure water used in the cleaner.

一般清洗液液面高于振動子表面0.5米以上為佳，由于多槽手動超聲波清洗機受駐波場的影響，波節處振幅很小，波幅處振幅大，所以為了避免造成清洗不均勻，應該注意使用合適的清洗液劑量，并將清洗物品位置應放在波幅處，這樣清洗效果就會更好。

Generally, the liquid level of cleaning fluid should be more than 0.5m above the surface of the vibrator. Because the multi slot manual Ultrasonic cleaning is affected by the standing wave field, the amplitude at the wave node is very small, and the amplitude at the wave amplitude is large, so in order to avoid uneven cleaning, attention should be paid to the use of appropriate cleaning fluid dosage, and the cleaning items should be placed at the wave amplitude, so that the cleaning effect will be better.

在使用多槽手動超聲波清洗機清洗一些較小的零件物品時經常需要使用清洗筐，但是清洗筐上的網眼會引起超聲衰減，所以要特別引起注意，注意選擇網眼大小合適的清洗籃，此外建議選用不銹鋼材質的清洗籃，盡量不要使用塑膠框，這樣能夠防止靜電的產生。

When using a multi slot manual Ultrasonic cleaning to clean some small parts, it is often necessary to use a cleaning basket. However, the mesh on the cleaning basket will cause ultrasonic attenuation, so special attention should be paid to the selection of a cleaning basket with an appropriate mesh size. In addition, it is recommended to select a cleaning basket made of stainless steel, and try not to use a plastic frame, so as to prevent the generation of static electricity.

通常在清洗時每道工序的時間定為三至五分鐘，如果被清洗物品的表面積比較大，或者工件的結構較為復雜時，要注意根據實際情況酌情調整多槽手動超聲波清洗機的清洗時間。若被清洗物容易出現重疊以及粘附的現象，那么在將被清洗物放入及取出槽液的時候可以抖動一下工件，讓清洗劑充分與工件接觸以提高清洗效果。

Usually, the cleaning time of each process is set as three to five minutes. If the surface area of the object to be cleaned is relatively large or the structure of the workpiece is complex, the cleaning time of the multi slot manual Ultrasonic cleaning should be adjusted according to the actual situation. If the cleaned object is prone to overlap and adhesion, the workpiece can be shaken when placing and removing the cleaned object from the tank, allowing the cleaning agent to fully contact the workpiece to improve the cleaning effect.

用多槽手動超聲波清洗機清洗工件要注意槽液不能加的太滿，以免發生兩槽超聲波清洗劑之間相互混合以及瀝干時清洗筐底部粘液的現象。此外，多槽手動超聲波清洗機的每個槽應為獨立的操作工序，注意不要將兩槽清洗劑相互串用或人為減少操作工序以及清洗的操作時間。

When using the multi tank manual Ultrasonic cleaning to clean the workpiece, it should be noted that the bath solution should not be too full, so as to avoid the phenomenon of mutual mixing of the two tank ultrasonic cleaning agents and the mucus at the bottom of the cleaning basket when draining. In addition, each tank of the multi tank manual Ultrasonic cleaning shall be an independent operation process, and attention shall be paid not to use the cleaning agent of the two tanks in series or reduce the operation process and cleaning operation time artificially.

使用以上幾種方法就能夠有效提高多槽手動超聲波清洗機的清洗潔凈度，大家在使用多槽手動超聲波清洗機的時候就要多注意。此外，每一種型號的超聲波清洗機都有著一定的差別，所以，在實際的應用過程中大家應該注意按照超聲波清洗機的操作說明書來清洗。還有什么問題歡迎來我們這里http://ckjy.net.cn咨詢！

Using the above methods can effectively improve the cleaning cleanliness of the multi slot manual Ultrasonic cleaning. Everyone should pay more attention when using the multi slot manual Ultrasonic cleaning. In addition, each model of Ultrasonic cleaning has certain differences, so in the actual application process, everyone should pay attention to cleaning according to the operating instructions of Ultrasonic cleaning. Do you have any further questions? Welcome to our place http://ckjy.net.cn consulting service